Gearbox Gen9

  • GATE – NanoAAB™ **Pre Order**

    0 out of 5
    NanoAAB NanoAAB is the latest, 3rd generation MOSFET with active brake. The application of the most up-to-date transistors and microprocessor enabled us to create the smallest and the most reliable MOSFET with active brake in the market. Thanks to its special coating, it is resistant to atmospheric conditions.
    $75.00
  • GATE – TITAN V2™ Advanced Set

    0 out of 5
    TITAN™ (drop-in mosfet) will transform your Gelblaster into an advanced training weapon system. Gain a tactical advantage thanks to the extremely fast trigger response, with an option of adjusting the Gelblaster for each mission with 20 functions. Give your Gelblaster a new lease of life!

    What is a drop-in mosfet? It is an electronic unit, which replaces the trigger contacts and the cut-off lever, which takes control of your Gelblaster.

    TITAN gives you the option to adjust:

    • Trigger sensitivity
    • Pre-cocking boost
    • Fire selector mode
    • Burst mode
    • Rate of fire
    • Low battery warning
    • Battery protection
    • Sniper delay

    TITAN V2™ Advanced Set

    At once you purchase TITAN with ADVANCED firmware edition, USB-Link and USB cables allowing to connect TITAN to PC as well as Android device. The ADVANCED firmware edition offers wide variety of functions and is dedicated for those who like complex solutions. It enables access to the Statistics and TITAN World Rankings. To learn all the differences between firmware editions, please check the comparison table. Kit contents:
    1. TITAN V2 with ADVANCED firmware edition (rear or front wired)
    2. USB-Link for GATE Control Station™ App
    3. USB Cables: a) USB-A to Micro-USB (1.5m / 4ft 11in) b) USB-C to Micro-USB (0.6m / 1ft 11in) c) Micro-USB to Micro-USB (0.6m / 1ft 11in)
    4. Installation Kit
    5. Quickstart Guides
    Mag wires not included.
    $260.00
  • GATE – TITAN V2™ Basic Set

    0 out of 5
    TITAN V2 Basic Module - the best if you long for having TITAN in two or more Gelblaster . Then you do not need the second USB-Link from the Advanced or Complete set. It includes TITAN with BASIC firmware edition. The BASIC firmware edition is an economic version with limited number of functions, dedicated for those who prefer simplicity but require highest quality.  If you decide to have more functions, there is always option to upgrade firmware from BASIC to ADVANCED.
    1. TITAN V2 with BASIC firmware edition (rear or front wired)
    2. Installation Kit
    3. Quickstart Guide
    Mag wires not included. NOTICE! In order to configure TITAN, you need the USB-Link or Tactical Programming Card which is not included in this kit. TITAN V2™ is an Gelblaster  Control System for V2 gearboxes which will transform your Gelblaster  into an advanced training weapon. Adjust your Gelblaster  using USB-Link and GATE Control Station app for PC and Android devices. Gain a tactical advantage thanks to the extremely fast trigger response, option of adjusting trigger sensitivity to your preferences and many other useful functions. Give your Gelblaster  a new lease of life! Thanks to the optical sensors we have eliminated the problem of faulty switches that can occur in competitors' drop-in mosfets. The trigger has no mechanical connections with the PCB. This eliminates mechanical stresses and provides for high reliability. Check full TITAN V2 description
    $155.00
  • GATE – WARFET™

    0 out of 5
    WARFET is GATE’s an advanced Gelblaster Control System. It has 20 functions and almost 6 million possible configurations. The outstanding Tactical Programming Card provides you with very easy access to the WARFET Power Module settings.
    $120.00
  • Gen9 Nylon Gearbox Shell

    0 out of 5
    $21.00
  • RetroArms CNC Gearbox V2 (8mm) w -QSC

    0 out of 5
    GBA Gel Blasters Australia have teamed up with RetroArms, as their exclusive Australian distributor. RetroArms is widely renowned for manufacturing the strongest, most precisely engineered gearbox. The RetroArms gearbox is constructed from one solid block of aircraft aluminium EN AW 7075 T651, which has higher strength (590MPa) than common construction steel (390MPa). Consequently, the RetroArms gearbox provides higher durability and resilience than the common zinc-aluminium counterparts. There is no other gearbox that comes close to comparing with the Retroarms precision, quality, strength and durability. The staggering 24 month warranty is testament to this statement. Package includes:
    • CNC Gearbox V2 (8mm)
    • Set of screws
    • QSC spring guide
    Product information:
    • RetroArms gearbox has a quick spring change system QSC, where you can pull out the whole spring guide with a hex key and change the spring without opening the gearbox.
    • Space for the trigger switch is designed for compatibility with trigger switches and trigger units from common manufacturers for example: Gate, etc.
    • CNC gearbox V2 has protective anodizing, even when it is problematic to anodize aluminium EN AW 7075 T651, because of its high strength and hardness. If we did not anodize products made from this material, there is a huge risk of corrosion (huge grey spots with rotten look).
    • Do not use brute force while installing screws. Use only 1 Nm when tightening the screws, so the screws are "just tight" enough, otherwise you risk threading the screw. If you want to be sure that screws will sit perfectly, use thread glue or thread colour.
    • You can use in our CNC gearbox any spring of your choice, but be aware that stronger springs will result in lower durability.
    • Spring holders have grooves, so the springs for the tappet plate and trigger switch will not jump off.
    • A groove has been added for the safety lever, so it will hold during installation.
    • A groove has been added for the trigger spring, for better fitting.
    • AOE (Angle of Engagement) control hole.
    • Sockets for bushings/bearings have a smaller diameter about -0.02mm (7.98mm), for non-overturning of the bushings during installation. The socket edges are cut down for better installation.
    • We have enhanced the grooves for wiring, so that you can use wiring up to 2.5mm in diameter.
    • Added a protective edge for wiring against the motor.
    • All threads are shaped instead of cut for better strength.
    • Both of the gearbox parts are centered by milled grooves and edges.
    • Added hole for releasing anti-reverse latch.
    • For better durability, we added more material around the cylinder head part of the gearbox, this was the most critical part and we added 100% more material where there is a huge radius.
    • Added groove for anti-reversal latch spring, so it will not jump off.
    • Outer edges are now cut off.
    Blaster Compatibility 
    • JM J10 ACR (with some modification)
    • Wells M401
    • M4A1 Gen9 (with modification)
    After market V2 receiver Compatibility
    • SLR
    • Xpower
    • LDT
    • Warintrest
    • Kubali
    Please chose a T-piece to suit The Magazine you want to use Well or Gen8/9
    $220.00
  • RetroArms CNC Split Gearbox V2 (8mm)

    5.00 out of 5
    GBA Gel Blasters Australia have teamed up with RetroArms, as their exclusive Australian distributor. RetroArms is widely renowned for manufacturing the strongest, most precisely engineered gearbox. The RetroArms gearbox is constructed from one solid block of aircraft aluminium EN AW 7075 T651, which has higher strength (590MPa) than common construction steel (390MPa). Consequently, the RetroArms gearbox provides higher durability and resilience than the common zinc-aluminium counterparts. There is no other gearbox that comes close to comparing with the Retroarms precision, quality, strength and durability. The staggering 24 month warranty is testament to this statement. Having a Split gearbox means, that this gearbox is designed as a two part, Upper and Lower. This gives the split gearbox many advantages, for example, making it easier to install internal parts into the gearbox. During setups of the cylinder set, there is no need of removing whole gearbox from your receiver, only the upper part needs be dismounted, because it‘s mounted on one receiver pin. Package includes:
    • CNC Split Gearbox V2 (8mm)
    • Set of screws
    • QSC spring guide
    Product information:
    • RetroArms gearbox has a quick spring change system QSC, where you can pull out the whole spring guide with a hex key and change the spring without opening the gearbox.
    • Space for the trigger switch is designed for compatibility with trigger switches and trigger units from common manufacturers for example: Gate, etc.
    • CNC gearbox V2 has protective anodizing, even when it is problematic to anodize aluminium EN AW 7075 T651, because of its high strength and hardness. If we did not anodize products made from this material, there is a huge risk of corrosion (huge grey spots with rotten look).
    • Do not use brute force while installing screws. Use only 1 Nm when tightening the screws, so the screws are "just tight" enough, otherwise you risk threading the screw. If you want to be sure that screws will sit perfectly, use thread glue or thread colour.
    • You can use in our CNC gearbox any spring of your choice, but be aware that stronger springs will result in lower durability.
    • Spring holders have grooves, so the springs for the tappet plate and trigger switch will not jump off.
    • A groove has been added for the safety lever, so it will hold during installation.
    • A groove has been added for the trigger spring, for better fitting.
    • AOE (Angle of Engagement) control hole.
    • Sockets for bushings/bearings have a smaller diameter about -0.02mm (7.98mm), for non-overturning of the bushings during installation. The socket edges are cut down for better installation.
    • We have enhanced the grooves for wiring, so that you can use wiring up to 2.5mm in diameter.
    • Added a protective edge for wiring against the motor.
    • All threads are shaped instead of cut for better strength.
    • Both of the gearbox parts are centered by milled grooves and edges.
    • Added hole for releasing anti-reverse latch.
    • For better durability, we added more material around the cylinder head part of the gearbox, this was the most critical part and we added 100% more material where there is a huge radius.
    • Added groove for anti-reversal latch spring, so it will not jump off.
    • Outer edges are now cut off.
    Blaster Compatibility 
    • JM J10 ACR (with some modification)
    • Wells M401
    • M4A1 Gen9 (with modification)
    After market V2 receiver Compatibility
    • SLR
    • Xpower
    • LDT
    • Warintrest
    • Kubali
    Please chose a T-piece to suit The Magazine you want to use Well or Gen8/9
    $247.00
  • SHS 7mm Bushes Pk 6

    0 out of 5
    SHS bushings can take all the stress your setup throws at it. Unlike ball bearing bushings, they won't break under high strain. When you purchase an Gel blaster, most likely it comes with platic bushings. Those plastic bushings break easily. Techs highly recommended you to upgrade your standard plastic bushings to solid metal Gel Blaster bushings. Manufacturer: SHS Size: 7mm Material: Steel Solid Metal Bushings Total of Six Bushings
    $15.00